BE植絨膠 BE flocking adhesive | 具有高牢度和耐水洗。 手感柔軟。 具有良好的相溶性。 植絨膠助劑能在常溫下架橋。 可運用機械和手工來植絨。 High fastness and washable Soft feel Good compatibility Flocking plastic additives can erect bridge at room temperature Mechanical and manual flocking can be used. | 置植絨膠於攪拌槽中，攪拌時逐漸加放植絨膠助劑，以達到均勻。 糊狀太稀加增稠劑調整。 印花過程中，漿料都需要保持適當稠度，才能展現清晰圖樣。 植絨膠若加入植絨膠交聯劑必需於當天用完。 印花後壓燙機壓燙轉移，壓燙溫度為150-170℃. 壓燙後冷撕，再經過隧道式烘乾機烘乾5分鐘。 Place the flocking adhesive in the stirred tank, gradually add flocking adhesive during stirring to achieve uniformity. Add thickener to thin paste In the printing process, paste is required to maintain proper consistency to show the clear pattern. If flocking cross-linking agent is added to the flocking adhesive, it must be used up in the day. After printing, the press machine makes pressing transfer and the pressing temperature is at 150-170℃ Make cold tear after pressing and dry for 5 minutes by a tunnel dryer. |
BE902台面轉移植絨漿 BE902 countertop transfer flocking paste | 手感好、牢度好、高粘度、易操作。 Good feel, good fastness, high viscosity, easy to operate. | 建議使用80-100目網紗。 印花2-3次，馬上把轉印紙放在漿料表面，用一個不漏漿的網板加入流動性好的水漿或者粘合劑，用比較硬的油性刮刀用力在花位上刮4-5刀，半小時後再撕去植絨紙。 有條件160度-170度烘乾最佳。 使用前須加2%的BE-868A水性交聯劑，並確保在12小時內使用完。 80-100mesh gauze is recommended. After 2-3 times of printing, immediately place the transfer paper on the paste surface; add good mobility slurry or adhesive by a screen without paste leakage, scrap for 4-5 times by hard oil scraper and then tear up the flock dusted paper half an hour later. It’s better to dry at 160-170℃ Before use, 2% of BE-868A water-based cross-linking agent shall be added and ensure to use up within 12h. |
BE903靜電植絨漿 BE903 electrostatic flocking paste | 手感好、牢度好、高粘度、易操作。 用於靜電植絨。 印花圖案輪廓鮮明。 Good feel, good fastness, high viscosity, easy to operate. For electrostatic flocking. Clean-cut prints. | 建議使用80-100目網紗。 使用前須加2%的BE-868水性交聯劑，並確保在12小時內使用完。 為確保水洗牢度，印刷過程中要確保漿料厚度，能夠使絨毛充分植入漿內，漿料粘度要適中，確保漿料流動性好，植絨漿一定要在表面未乾之前植絨，否則絨毛不能充分植入漿內，達不到水洗牢度要求。 水洗測試前應確保印花完全乾透，否則會影響測試效果。 有條件160度-170度烘乾最佳。 80-100mesh gauze is recommended. Before use, 2% of BE-868A water-based cross-linking agent shall be added and ensure to use up within 12h. To ensure the wash fastness, the paste thickness shall be ensured in the printing process to allow the fluff to fully implant in the paste; the paste viscosity should be moderate, ensure good fluidity; flocking shall be made before the drying of surface, otherwise the fluff cannot be fully implanted in the fluff and fail to achieve the wash fastness requirements. Make sure the printing is completely dry before washing test; otherwise it may affect the test results. It’s better to dry at 160-170℃ |
