BE植绒胶 BE flocking adhesive | 具有高牢度和耐水洗。 手感柔软。 具有良好的相溶性。 植绒胶助剂能在常温下架桥。 可运用机械和手工来植绒。 High fastness and washable Soft feel Good compatibility Flocking plastic additives can erect bridge at room temperature Mechanical and manual flocking can be used. | 置植绒胶于搅拌槽中，搅拌时逐渐加放植绒胶助剂，以达到均匀。 糊状太稀加增稠剂调整。 印花过程中，浆料都需要保持适当稠度，才能展现清晰图样。 植绒胶若加入植绒胶交联剂必需于当天用完。 印花后压烫机压烫转移，压烫温度为150-170℃. 压烫后冷撕，再经过隧道式烘干机烘干5分钟。 Place the flocking adhesive in the stirred tank, gradually add flocking adhesive during stirring to achieve uniformity. Add thickener to thin paste In the printing process, paste is required to maintain proper consistency to show the clear pattern. If flocking cross-linking agent is added to the flocking adhesive, it must be used up in the day. After printing, the press machine makes pressing transfer and the pressing temperature is at 150-170℃ Make cold tear after pressing and dry for 5 minutes by a tunnel dryer. |
BE902台面转移植绒浆 BE902 countertop transfer flocking paste | 手感好、牢度好、高粘度、易操作。 Good feel, good fastness, high viscosity, easy to operate. | 建议使用80-100目网纱。 印花2-3次，马上把转印纸放在浆料表面，用一个不漏浆的网板加入流动性好的水浆或者粘合剂，用比较硬的油性刮刀用力在花位上刮4-5刀，半小时后再撕去植绒纸。 有条件160度-170度烘干最佳。 使用前须加2%的BE-868A水性交联剂，并确保在12小时内使用完。 80-100mesh gauze is recommended. After 2-3 times of printing, immediately place the transfer paper on the paste surface; add good mobility slurry or adhesive by a screen without paste leakage, scrap for 4-5 times by hard oil scraper and then tear up the flock dusted paper half an hour later. It’s better to dry at 160-170℃ Before use, 2% of BE-868A water-based cross-linking agent shall be added and ensure to use up within 12h. |
BE903静电植绒浆 BE903 electrostatic flocking paste | 手感好、牢度好、高粘度、易操作。 用于静电植绒。 印花图案轮廓鲜明。 Good feel, good fastness, high viscosity, easy to operate. For electrostatic flocking. Clean-cut prints. | 建议使用80-100目网纱。 使用前须加2%的BE-868水性交联剂，并确保在12小时内使用完。 为确保水洗牢度，印刷过程中要确保浆料厚度，能够使绒毛充分植入浆内，浆料粘度要适中，确保浆料流动性好，植绒浆一定要在表面未干之前植绒，否则绒毛不能充分植入浆内，达不到水洗牢度要求。 水洗测试前应确保印花完全干透，否则会影响测试效果。 有条件160度-170度烘干最佳。 80-100mesh gauze is recommended. Before use, 2% of BE-868A water-based cross-linking agent shall be added and ensure to use up within 12h. To ensure the wash fastness, the paste thickness shall be ensured in the printing process to allow the fluff to fully implant in the paste; the paste viscosity should be moderate, ensure good fluidity; flocking shall be made before the drying of surface, otherwise the fluff cannot be fully implanted in the fluff and fail to achieve the wash fastness requirements. Make sure the printing is completely dry before washing test; otherwise it may affect the test results. It’s better to dry at 160-170℃ |
